KONFIGURASI ROUTER RIP Version 2

With Cisco Packet Tracer

Langkah-Langkah Yang Harus Anda Lakukan :

1.      Buka Program Cisco Packet Tracer.

2.   Pilih peralatan yang akan dipakai yaitu : 3 buah Router, 2 buah kabel Cross-Over, 2 buah kabel Serial DCE/DTE dan 2 buah PC.

3.      Atur peralatan sesuai dengan sketsa gambar di atas.

4.      Hubungkan Router dengan Router menggunakan kabel Serial DCE/DTE.

5.      Hubungkan Router dengan PC menggunakan kabel Cross-Over.

6.      Setting PC dan Router seperti di bawah ini :

Konfigurasi PC0 dan PC1 :

 

Konfigurasi Router :

1.     Router0

Router#ena

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#int fa0/0

Router(config-if)#ip add 10.1.0.1 255.255.0.0

Router(config-if)#no shut

Router(config-if)#exit

Router(config)#int ser2/0

Router(config-if)#ip add 10.2.0.1 255.255.0.0

Router(config-if)#clock rate 64000

Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down

Router(config-if)#exit

Router(config)#router rip

Router(config-router)#version 2

Router(config-router)#network 10.1.0.0

Router(config-router)#network 10.2.0.0

Router(config-router)#exit

Router(config)#^Z

Router#

%SYS-5-CONFIG_I: Configured from console by console

Router#wr mem

Building configuration...

[OK]

Router#

Router#sh ip route

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area

       * - candidate default, U - per-user static route, o - ODR

       P - periodic downloaded static route

Gateway of last resort is not set

     10.0.0.0/16 is subnetted, 4 subnets

C       10.1.0.0 is directly connected, FastEthernet0/0

C       10.2.0.0 is directly connected, Serial2/0

R       10.3.0.0 [120/1] via 10.2.0.2, 00:00:23, Serial2/0

R       10.4.0.0 [120/2] via 10.2.0.2, 00:00:23, Serial2/0

Router#

2.     Router1

Router>ena

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#int ser2/0

Router(config-if)#ip add 10.2.0.2 255.255.0.0

Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#exit

Router(config)#int ser3/0

Router(config-if)#ip add 10.3.0.1 255.255.0.0

Router(config-if)#clock rate 64000

Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down

Router(config-if)#exit

Router(config)#router rip

Router(config-router)#version 2

Router(config-router)#network 10.2.0.0

Router(config-router)#network 10.3.0.0

Router(config-router)#exit

Router(config)#^Z

Router#

%SYS-5-CONFIG_I: Configured from console by console

Router#wr mem

Building configuration...

[OK]

Router#

Router#sh ip route

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area

       * - candidate default, U - per-user static route, o - ODR

       P - periodic downloaded static route

Gateway of last resort is not set

     10.0.0.0/16 is subnetted, 4 subnets

R       10.1.0.0 [120/1] via 10.2.0.1, 00:00:11, Serial2/0

C       10.2.0.0 is directly connected, Serial2/0

C       10.3.0.0 is directly connected, Serial3/0

R       10.4.0.0 [120/1] via 10.3.0.2, 00:00:07, Serial3/0

Router#

3.     Router2

Router>ena

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#int fa0/0

Router(config-if)#ip add 10.4.0.1 255.255.0.0

Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit

Router(config)#int ser3/0

Router(config-if)#ip add 10.3.0.2 255.255.0.0

Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to up

Router(config-if)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to up

Router(config-if)#exit

Router(config)#router rip

Router(config-router)#version 2

Router(config-router)#network 10.3.0.0

Router(config-router)#network 10.4.0.0

Router(config-router)#exit

Router(config)#^Z

Router#

%SYS-5-CONFIG_I: Configured from console by console

Router#wr mem

Building configuration...

[OK]

Router#

Router#sh ip route

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area

       * - candidate default, U - per-user static route, o - ODR

       P - periodic downloaded static route

Gateway of last resort is not set

     10.0.0.0/16 is subnetted, 4 subnets

R       10.1.0.0 [120/2] via 10.3.0.1, 00:00:25, Serial3/0

R       10.2.0.0 [120/1] via 10.3.0.1, 00:00:25, Serial3/0

C       10.3.0.0 is directly connected, Serial3/0

C       10.4.0.0 is directly connected, FastEthernet0/0

Router#

  

Pengecekan Koneksi :

1.      PC0 ke PC1 ( Ping 10.4.0.2 )

 

2.      PC1 ke PC0 ( Ping 10.1.0.2 )

  
Bila terkoneksi semua berarti berhasil.