Kamis, 29 Desember 2011

HTML Codes - Table of ascii characters and symbols











































**source:http://www.ascii.cl/htmlcodes.htm **
Diposting oleh Berbagi Selalu di 20.29 0 komentar

Rabu, 14 Desember 2011

KONFIGURASI ROUTER RIP Version 2


With Cisco Packet Tracer





















Langkah-Langkah Yang Harus Anda Lakukan :

1.      Buka Program Cisco Packet Tracer.
2.   Pilih peralatan yang akan dipakai yaitu : 3 buah Router, 2 buah kabel Cross-Over, 2 buah kabel Serial DCE/DTE dan 2 buah PC.
3.      Atur peralatan sesuai dengan sketsa gambar di atas.
4.      Hubungkan Router dengan Router menggunakan kabel Serial DCE/DTE.
5.      Hubungkan Router dengan PC menggunakan kabel Cross-Over.
6.      Setting PC dan Router seperti di bawah ini :

Konfigurasi PC0 dan PC1 :

 









Konfigurasi Router :

1.     Router0
Router#ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 10.1.0.1 255.255.0.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 10.2.0.1 255.255.0.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#network 10.1.0.0
Router(config-router)#network 10.2.0.0
Router(config-router)#exit
Router(config)#^Z
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#wr mem
Building configuration...
[OK]
Router#
Router#sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route

Gateway of last resort is not set

     10.0.0.0/16 is subnetted, 4 subnets
C       10.1.0.0 is directly connected, FastEthernet0/0
C       10.2.0.0 is directly connected, Serial2/0
R       10.3.0.0 [120/1] via 10.2.0.2, 00:00:23, Serial2/0
R       10.4.0.0 [120/2] via 10.2.0.2, 00:00:23, Serial2/0
Router#

2.     Router1
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int ser2/0
Router(config-if)#ip add 10.2.0.2 255.255.0.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#exit
Router(config)#int ser3/0
Router(config-if)#ip add 10.3.0.1 255.255.0.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#network 10.2.0.0
Router(config-router)#network 10.3.0.0
Router(config-router)#exit
Router(config)#^Z
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#wr mem
Building configuration...
[OK]
Router#
Router#sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route

Gateway of last resort is not set

     10.0.0.0/16 is subnetted, 4 subnets
R       10.1.0.0 [120/1] via 10.2.0.1, 00:00:11, Serial2/0
C       10.2.0.0 is directly connected, Serial2/0
C       10.3.0.0 is directly connected, Serial3/0
R       10.4.0.0 [120/1] via 10.3.0.2, 00:00:07, Serial3/0
Router#

3.     Router2
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 10.4.0.1 255.255.0.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser3/0
Router(config-if)#ip add 10.3.0.2 255.255.0.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to up
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to up
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#network 10.3.0.0
Router(config-router)#network 10.4.0.0
Router(config-router)#exit
Router(config)#^Z
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#wr mem
Building configuration...
[OK]
Router#
Router#sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route

Gateway of last resort is not set

     10.0.0.0/16 is subnetted, 4 subnets
R       10.1.0.0 [120/2] via 10.3.0.1, 00:00:25, Serial3/0
R       10.2.0.0 [120/1] via 10.3.0.1, 00:00:25, Serial3/0
C       10.3.0.0 is directly connected, Serial3/0
C       10.4.0.0 is directly connected, FastEthernet0/0
Router#

  
Pengecekan Koneksi :

1.      PC0 ke PC1 ( Ping 10.4.0.2 )

















 

2.      PC1 ke PC0 ( Ping 10.1.0.2 )

















  
Bila terkoneksi semua berarti berhasil.
Diposting oleh Berbagi Selalu di 17.39 0 komentar
Label:
Langganan: Postingan (Atom)